Post by Stubbo on Nov 2, 2015 19:43:45 GMT -5
2016 Tasman Cup
In the early 1960’s, discussions between the Association of New Zealand Car Clubs, the Confederation of Australian Motor Sport and representatives of the international promoters in both countries materialized into what became known as the Tasman Cup series of races. This was, in effect, a "minor league" World Racing Drivers' Championship. It had the effect of enhancing the prestige of motor racing in New Zealand and Australia and also stimulated keener competition between New Zealand and Australian drivers in races on both sides of the Tasman Sea.
For the Tasman Cup the points scoring system was similar to the then current system used for the world title. There were eight races, four in each country, although some years Australia only held three races.
This eight-round series created greater public interest in motor racing in this part of the world, particularly as it was conducted during the European off-season.
So, the Tasman Cup Proxy Series will be a 7 race series to be held in from April through to July 2016.
The series is open to that competed in the original Tasman Cup series in 1964 and 1965 and for cars from the 1961 -65 1.5 litre GP era.
For details of eligible GP cars of the check out the VRAA (Vintage Race Across America). There is a lot of information available there.
For eligible Tasman Cup cars visit www.sergent.com.au which has a wealth of information in relation to the original Tasman Series and details all of the cars that competed in that series.
The rules of the Tasman Cup are slightly different to those of the VRAA. Please check carefully.
Please note that there will be a separate thread to use for your nominations.
Rules for the 2016 Tasman Cup series.
This will start the official entry list, establish the schedule and contain the rules of the 2016 Tasman Cup proxy series. If you want to compete in the 2016 Tasman Cup, then please read through the following information and confirm your entry with a reply in entry list thread.
All entries need to be paid by the 1st March 2016.
Cars to be in Australia by Friday the 1st April 2016.
Cars will be returned to their owners at or around the end of July.
At this stage we will have a 7 race series. The probable schedule is
Round 1, Victoria mid/late April
Round 2, Tasmania late April/early May
Round 3, Tasmania Mid May
Round 4, New South Wales Late May/early June
Round 5, South Australia Mid June
Round 6, South Australia Late June/early July
Round 7, Victoria, mid/late July.
2016 Tasman Cup Participants:
The maximum size of the field is limited to 24 cars. A reserve list will be started if there are more than 24 people interested in entering.
Returning entrants will be given priority. All returning entrants must nominate by 15th of January 2016. From that date any entries on the reserve list will be included in the order in which their nomination was received
Entry fee for Australian and NZ entrants will be $25.00AUD. For International Competitors the entry fee will be $30.00AUD. Any surplus money will be allocated to the prize pool.
Any offers of sponsorship or donation of prizes will be greatly appreciated.
When nominating please provide the following information about your car if possible.
Car number, duplicates will NOT be allowed. Returning entrants will have their number reserved for them until the 15th January 2016.
Number 1 is reserved for the previous series winner.
Car make and model.
Resin, Plastic or Fibreglass body.
Chassis type.
Your name, very important. Owners name should be written on the bottom of the chassis.
VRAA cars are eligible
Phil Kalbfell offers a range of resin bodies that are suitable for this series.
Eligible Tasman Cup Cars
For eligible Tasman Cup cars please PM me and I can send you a list.
For eligible VRAA cars please check out the VRAA series or PM me and I can send you a list.
Tasman Cup constructors guide lines
Please read the rules carefully. They differ slightly from the VRAA rules.
Cars should be 1/32 scale models of cars that competed in the Tasman Cup in 1964 or 1965. The series is also open to 1/32 scale models of F1 cars from the 1961-65 1.5 litre period..
Only hard bodies (resin, fibreglass, injection moulded plastic, or fabricated plastic) will be allowed.
Reasonable scale appearance and representation of authentic colour/number/driver schemes (but no need to replicate specific cars or drivers; freelance schemes may be used, if period-appropriate).
We would encourage entrants to create their own liveries (in correct period style of course).
Minimum detail would include clear windscreen; driver with head, arms, hands, and partial steering wheel; roll bar; some 3-D engine detail if visible on actual model, exhaust system. Mirrors and suspension detail are required.
Phil Kalbfell offers a range of resin bodies that are suitable for this series.
Chassis may be fabricated using any material or stock manufactured excluding carbon fibre.
Wheels, inserts and tyres (see below for limits) should be in keeping with the period.
Tyres
Rears: 0.80" (20.32mm) minimum diameter, maximum width .276" (7.25mm). at the sidewall
Fronts: 0.75" (19.05mm) minimum diameter, Maximum width 245” {6.25mm). at the sidewall. Front tyres must have a minimum width of 4.75mm at the sidewall.
Rear tyres should have a contact patch of not more than 7mm width, fronts no more than 6mm, where the tyre meets the track at the start of the series. If you are running a 4wd car then the front tyres may be the same size as the rear.
Rubber or urethane tyre compound must be black, no chemicals or oil. No clear paint or polish on front tyres.
Rear tyres may not be slab sided tyres like YellowDogs. All rear tyres must have the sidewall bulge like the rear cars did in the era. The inner sidewall does not have to have the bulge but must be radiused at the tread area.
Motors
You may choose from one of the following.
BWA FF050,
Solarbotics FF030,
MRRC SRP-1090 FF-050. This motor is also known as the SRP slim can Power 16
Vanski FF050 bearing the markings PPN13EB10C.
Gears may not be visible from above except as follows.
Some 1:1 cars had shortish bodies at the rear and the bodywork finished close to the rear axle line. If you want to model and enter one of these cars please let me know ASAP and if I can verify the short bodywork I will allow the crown to be exposed.
But please don’t ask me is this legal? Or is that legal? If you want to enter such a car check it out and provide me with the details and hopefully a photo and then I can confirm if it will be OK or not.
I know that some Tasman Brabhams had the short back end.
Dimensions
Minimum ground clearance 1/16" or .0625", or 1.59 mm except at gear.
Accurate wheelbase (tolerance of +/- 1.5mm).
The cars can only have a max width of 2” or 50.8 mm, sidewall to sidewall.
Guide not to be visible from directly above the car in the straight ahead position.
No traction magnets.
Owners name should be written on the bottom of the chassis.
Race Procedures
Finishing order for each round of the proxy race, and the entire series, will be determined by number of laps and 10ths of laps, within a set amount of time. A minimum of 9 minutes and a maximum of 12 minutes racing time per car is required at each track.
Each race will be conducted according to procedures chosen by the individual track host. Each car is to be raced in a fair and equal manner, and subject to the same track conditions. Each driver should drive all cars for the same time on the same lane. Lane and driver rotations to be determined by track host.
Track voltage will be 12 volts and will remain equal for all lanes throughout the race.
A running inspection of cars is to be made before and after each race. Cars may be cleaned and lubricated. No penalties for repairs required to keep the cars in the race. This excludes functional tyre and motor changes. If a motor should fail during qualifying or during the race it can be replaced after the race has been completed without penalty. Before repairs to any damage to the body or chassis are made, the track host will discuss with the car owner for repair or return instructions.
Points Scoring
For each race;
50-44-40-36-34-30-28-26-24-22-18-16-14-12-10-9-8-7-6-5-4-3-2-1 with a fast race lap bonus of 2 points.
The fastest qualifier for each round will receive a bonus of 3 points
In the case of a tie a count back system will apply. If two or more cars finish on the same points then the car with the most wins will be declared the winner. If still tied then the most second placings will apply and so on and so on down the finishing order. If after that we still have a tie we will determine which car had faster lap times on the various tracks. If after that we still have a tie then we reckon we will have had a bloody good series.
The Race Directors will have the final decision. Should one of the Race Directors cars be involved in a tie and the finishing order is still in dispute we will seek advice and input from one or more of the track hosts. I could be magnanimous here and say the Race Director will concede. Maybe he will.
Penalties
Please be sure you avoid incurring any.
Late arrivals. Tough. The series will kick off on the scheduled date and if your car is stuck in the mail it will miss any round that it misses. The car will be tech’d on arrival and then sent on to the next practicable venue for inclusion in the remainder of the series.
Any car outside reasonable rule boundaries and with magnetic down force will be sent home.
Any car that requires a tyre change during the series will incur a penalty per set changed.
All costs incurred will be paid by the entrant.
SCHEDULE OF PENALTIES
Late arrival for scrutineering 20 points
Remedying of other non-compliant matters 10 points
Car outside above mechanical rules 10 points per round
Non-compliance other than mechanical 10 points
Tyre change 10 points
Happy Racing
In the early 1960’s, discussions between the Association of New Zealand Car Clubs, the Confederation of Australian Motor Sport and representatives of the international promoters in both countries materialized into what became known as the Tasman Cup series of races. This was, in effect, a "minor league" World Racing Drivers' Championship. It had the effect of enhancing the prestige of motor racing in New Zealand and Australia and also stimulated keener competition between New Zealand and Australian drivers in races on both sides of the Tasman Sea.
For the Tasman Cup the points scoring system was similar to the then current system used for the world title. There were eight races, four in each country, although some years Australia only held three races.
This eight-round series created greater public interest in motor racing in this part of the world, particularly as it was conducted during the European off-season.
So, the Tasman Cup Proxy Series will be a 7 race series to be held in from April through to July 2016.
The series is open to that competed in the original Tasman Cup series in 1964 and 1965 and for cars from the 1961 -65 1.5 litre GP era.
For details of eligible GP cars of the check out the VRAA (Vintage Race Across America). There is a lot of information available there.
For eligible Tasman Cup cars visit www.sergent.com.au which has a wealth of information in relation to the original Tasman Series and details all of the cars that competed in that series.
The rules of the Tasman Cup are slightly different to those of the VRAA. Please check carefully.
Please note that there will be a separate thread to use for your nominations.
Rules for the 2016 Tasman Cup series.
This will start the official entry list, establish the schedule and contain the rules of the 2016 Tasman Cup proxy series. If you want to compete in the 2016 Tasman Cup, then please read through the following information and confirm your entry with a reply in entry list thread.
All entries need to be paid by the 1st March 2016.
Cars to be in Australia by Friday the 1st April 2016.
Cars will be returned to their owners at or around the end of July.
At this stage we will have a 7 race series. The probable schedule is
Round 1, Victoria mid/late April
Round 2, Tasmania late April/early May
Round 3, Tasmania Mid May
Round 4, New South Wales Late May/early June
Round 5, South Australia Mid June
Round 6, South Australia Late June/early July
Round 7, Victoria, mid/late July.
2016 Tasman Cup Participants:
The maximum size of the field is limited to 24 cars. A reserve list will be started if there are more than 24 people interested in entering.
Returning entrants will be given priority. All returning entrants must nominate by 15th of January 2016. From that date any entries on the reserve list will be included in the order in which their nomination was received
Entry fee for Australian and NZ entrants will be $25.00AUD. For International Competitors the entry fee will be $30.00AUD. Any surplus money will be allocated to the prize pool.
Any offers of sponsorship or donation of prizes will be greatly appreciated.
When nominating please provide the following information about your car if possible.
Car number, duplicates will NOT be allowed. Returning entrants will have their number reserved for them until the 15th January 2016.
Number 1 is reserved for the previous series winner.
Car make and model.
Resin, Plastic or Fibreglass body.
Chassis type.
Your name, very important. Owners name should be written on the bottom of the chassis.
VRAA cars are eligible
Phil Kalbfell offers a range of resin bodies that are suitable for this series.
Eligible Tasman Cup Cars
For eligible Tasman Cup cars please PM me and I can send you a list.
For eligible VRAA cars please check out the VRAA series or PM me and I can send you a list.
Tasman Cup constructors guide lines
Please read the rules carefully. They differ slightly from the VRAA rules.
Cars should be 1/32 scale models of cars that competed in the Tasman Cup in 1964 or 1965. The series is also open to 1/32 scale models of F1 cars from the 1961-65 1.5 litre period..
Only hard bodies (resin, fibreglass, injection moulded plastic, or fabricated plastic) will be allowed.
Reasonable scale appearance and representation of authentic colour/number/driver schemes (but no need to replicate specific cars or drivers; freelance schemes may be used, if period-appropriate).
We would encourage entrants to create their own liveries (in correct period style of course).
Minimum detail would include clear windscreen; driver with head, arms, hands, and partial steering wheel; roll bar; some 3-D engine detail if visible on actual model, exhaust system. Mirrors and suspension detail are required.
Phil Kalbfell offers a range of resin bodies that are suitable for this series.
Chassis may be fabricated using any material or stock manufactured excluding carbon fibre.
Wheels, inserts and tyres (see below for limits) should be in keeping with the period.
Tyres
Rears: 0.80" (20.32mm) minimum diameter, maximum width .276" (7.25mm). at the sidewall
Fronts: 0.75" (19.05mm) minimum diameter, Maximum width 245” {6.25mm). at the sidewall. Front tyres must have a minimum width of 4.75mm at the sidewall.
Rear tyres should have a contact patch of not more than 7mm width, fronts no more than 6mm, where the tyre meets the track at the start of the series. If you are running a 4wd car then the front tyres may be the same size as the rear.
Rubber or urethane tyre compound must be black, no chemicals or oil. No clear paint or polish on front tyres.
Rear tyres may not be slab sided tyres like YellowDogs. All rear tyres must have the sidewall bulge like the rear cars did in the era. The inner sidewall does not have to have the bulge but must be radiused at the tread area.
Motors
You may choose from one of the following.
BWA FF050,
Solarbotics FF030,
MRRC SRP-1090 FF-050. This motor is also known as the SRP slim can Power 16
Vanski FF050 bearing the markings PPN13EB10C.
Gears may not be visible from above except as follows.
Some 1:1 cars had shortish bodies at the rear and the bodywork finished close to the rear axle line. If you want to model and enter one of these cars please let me know ASAP and if I can verify the short bodywork I will allow the crown to be exposed.
But please don’t ask me is this legal? Or is that legal? If you want to enter such a car check it out and provide me with the details and hopefully a photo and then I can confirm if it will be OK or not.
I know that some Tasman Brabhams had the short back end.
Dimensions
Minimum ground clearance 1/16" or .0625", or 1.59 mm except at gear.
Accurate wheelbase (tolerance of +/- 1.5mm).
The cars can only have a max width of 2” or 50.8 mm, sidewall to sidewall.
Guide not to be visible from directly above the car in the straight ahead position.
No traction magnets.
Owners name should be written on the bottom of the chassis.
Race Procedures
Finishing order for each round of the proxy race, and the entire series, will be determined by number of laps and 10ths of laps, within a set amount of time. A minimum of 9 minutes and a maximum of 12 minutes racing time per car is required at each track.
Each race will be conducted according to procedures chosen by the individual track host. Each car is to be raced in a fair and equal manner, and subject to the same track conditions. Each driver should drive all cars for the same time on the same lane. Lane and driver rotations to be determined by track host.
Track voltage will be 12 volts and will remain equal for all lanes throughout the race.
A running inspection of cars is to be made before and after each race. Cars may be cleaned and lubricated. No penalties for repairs required to keep the cars in the race. This excludes functional tyre and motor changes. If a motor should fail during qualifying or during the race it can be replaced after the race has been completed without penalty. Before repairs to any damage to the body or chassis are made, the track host will discuss with the car owner for repair or return instructions.
Points Scoring
For each race;
50-44-40-36-34-30-28-26-24-22-18-16-14-12-10-9-8-7-6-5-4-3-2-1 with a fast race lap bonus of 2 points.
The fastest qualifier for each round will receive a bonus of 3 points
In the case of a tie a count back system will apply. If two or more cars finish on the same points then the car with the most wins will be declared the winner. If still tied then the most second placings will apply and so on and so on down the finishing order. If after that we still have a tie we will determine which car had faster lap times on the various tracks. If after that we still have a tie then we reckon we will have had a bloody good series.
The Race Directors will have the final decision. Should one of the Race Directors cars be involved in a tie and the finishing order is still in dispute we will seek advice and input from one or more of the track hosts. I could be magnanimous here and say the Race Director will concede. Maybe he will.
Penalties
Please be sure you avoid incurring any.
Late arrivals. Tough. The series will kick off on the scheduled date and if your car is stuck in the mail it will miss any round that it misses. The car will be tech’d on arrival and then sent on to the next practicable venue for inclusion in the remainder of the series.
Any car outside reasonable rule boundaries and with magnetic down force will be sent home.
Any car that requires a tyre change during the series will incur a penalty per set changed.
All costs incurred will be paid by the entrant.
SCHEDULE OF PENALTIES
Late arrival for scrutineering 20 points
Remedying of other non-compliant matters 10 points
Car outside above mechanical rules 10 points per round
Non-compliance other than mechanical 10 points
Tyre change 10 points
Happy Racing